Supplementing a “more miles per gallon” movement in 1919, a series of experiments outlined by the S. A. E. Committee on Utilization of Present Fuels was undertaken by the Bureau of Standards, in May, 1920, which included measurements of engine performance under conditions of both steady running and rapid acceleration with different temperatures of the intake charge secured by supplying heated air to the carbureter from a hot-air stove, by maintaining a uniformly heated intake manifold and by using a hot-spot manifold, fuel economy being determined for both part and full-throttle operation. A typical six-cylinder engine was used, having a two-port intake manifold with a minimum length of passage within the cylinder block, an exhaust manifold conveniently located for installing special exhaust openings, rather high peak-load speed and conventional general design. The carbureter was selected with the requirements in view of securing definite and measurable conditions of the intake charge and accurate measurements of the behavior of the charge as indicated by fuel consumption in pounds per brake-horsepower-hour. Provision was made for an unusually complete series of measurements. These are described, the most unique being the construction of the tee portion of the manifold of Pyrex glass. Motion pictures of the manifold were taken during operation, but in only one run were the walls completely dry, and a surprising amount of directly applied heat was required to accomplish this.The main series of runs was made with the exhaust-jacket manifold, in an attempt to determine how best to obtain low fuel consumption and rapid acceleration and how this result was influenced by changes in the amount of heat furnished the intake charge or in the method of supplying this heat. The fuel consumption tests were made at both full and half load at speeds of 650 and 1200 r.p.m. Full details of the tests are then stated, the results are presented in charts, and these are discussed. The results obtained are then summarized as follows: Supplementing a “more miles per gallon” movement in 1919, a series of experiments outlined by the S. A. E. Committee on Utilization of Present Fuels was undertaken by the Bureau of Standards, in May, 1920, which included measurements of engine performance under conditions of both steady running and rapid acceleration with different temperatures of the intake charge secured by supplying heated air to the carbureter from a hot-air stove, by maintaining a uniformly heated intake manifold and by using a hot-spot manifold, fuel economy being determined for both part and full-throttle operation. A typical six-cylinder engine was used, having a two-port intake manifold with a minimum length of passage within the cylinder block, an exhaust manifold conveniently located for installing special exhaust openings, rather high peak-load speed and conventional general design. The carbureter was selected with the requirements in view of securing definite and measurable conditions of the intake charge and accurate measurements of the behavior of the charge as indicated by fuel consumption in pounds per brake-horsepower-hour. Provision was made for an unusually complete series of measurements. These are described, the most unique being the construction of the tee portion of the manifold of Pyrex glass. Motion pictures of the manifold were taken during operation, but in only one run were the walls completely dry, and a surprising amount of directly applied heat was required to accomplish this.The main series of runs was made with the exhaust-jacket manifold, in an attempt to determine how best to obtain low fuel consumption and rapid acceleration and how this result was influenced by changes in the amount of heat furnished the intake charge or in the method of supplying this heat. The fuel consumption tests were made at both full and half load at speeds of 650 and 1200 r.p.m. Full details of the tests are then stated, the results are presented in charts, and these are discussed. The results obtained are then summarized as follows:


    Zugriff

    Zugriff prüfen

    Verfügbarkeit in meiner Bibliothek prüfen

    Bestellung bei Subito €


    Exportieren, teilen und zitieren



    Titel :

    INTAKE-MANIFOLD TEMPERATURES AND FUEL ECONOMY


    Weitere Titelangaben:

    Sae Technical Papers


    Beteiligte:
    DICKINSON, H C (Autor:in) / SPARROW, S W (Autor:in) / JAMES, W S (Autor:in)

    Kongress:

    Pre-1964 SAE Technical Papers ; 1906



    Erscheinungsdatum :

    1920-01-01




    Medientyp :

    Aufsatz (Konferenz)


    Format :

    Print


    Sprache :

    Englisch




    Intake manifold fuel film transient dynamics

    Bardon,M.F. / Rao,V.K. / Gardiner,D.P. et al. | Kraftfahrwesen | 1987


    Intake Manifold Length Effects on Turbocharged Gasoline Downsizing Engine Performance and Fuel Economy

    Gurney, David / Taylor, James / Stehlig, Jürgen et al. | SAE Technical Papers | 2012


    Intake Manifold Fuel Film Transient Dynamics

    Gardiner, D.P. / Bardon, M.F. / Rao, V.K. | SAE Technical Papers | 1987


    Intake Manifold Length Effects on Turbocharged Gasoline Downsizing Engine Performance and Fuel Economy

    Taylor, J. / Gurney, D. / Freeland, P. et al. | British Library Conference Proceedings | 2012


    Intake manifold

    ITAGAKI KEISUKE | Europäisches Patentamt | 2020

    Freier Zugriff