81–100 of 110 hits
|

    Numerical Optimization of Vacuum Assisted Manufacturing of Aircraft Composite Parts Using the Predictive Assessment of Objectives

    Shevtsov, Sergey / Zhilyaev, Igor / Huang, Jyun-Ping et al. | IEEE | 2021
    the dependence of the resin viscosity on the degree of cure and temperature, as well as for the diffusion coefficient of the degree of cure ...

    Envelope Protection Reconfiguration for Iced Aircraft

    Zheng, Sizhuang / Wang, Lixin / Yue, Ting et al. | IEEE | 2021
    Ice accretion is an important factor that affects the flight safety of civil aircraft, and reconfiguration of the envelop protection ...

    Aerodynamic Performance of a Two-Dimensional Flapping Elliptic Airfoil in Ground Proximity

    Sinha, Jit / Dash, Sunil Manohar | IEEE | 2021
    varied the mean ground clearances of the airfoil, flapping frequency, and pivot location on the airfoil. However, the Reynolds number of the ...

    Trajectory Planning Method of UAVs Considering the Error Correction

    Wu, Jianwei / Zhou, Yang / Chen, Lin et al. | IEEE | 2021
    method with multi-steps optimization. The optimal trajectory of the UAV is obtained by solving the program developed on MATLAB. The results ...

    Control of Interconnected Drones

    Oland, Espen | IEEE | 2021
    of drones, and is based on the principle of sharing the load between the different drones. Simulations show the potenial of the work by ...

    Numerical Investigation of Dynamic Properties of The Beam with Segmented Acoustic Black Hole Indentations

    Fu, Qidi / Zhang, Jianrun | IEEE | 2021
    ratio have also been calculated. The calculation results show that segmented ABH beam can better gather energy on the tip of ABH structure and ...

    Numerical Simulations of Two-Dimensional Hypersonic Inlet At Finite Flight Angles

    Bian, Fang / Cai, Qiang / Sun, Lin et al. | IEEE | 2021
    its formation based on the basic theory of aerodynamic, providing the necessary reference for the inlet design and performance estimation. At ...

    Backstepping Control for Asymmetric Fighter Aircraft Executing the High Alpha Herbst Maneuver

    Khanna, Anukaran / Mukherjee, Bijoy K. | IEEE | 2021
    asymmetric center- of-gravity shift as nonlinearity and dynamics get more complex, under such situation implementation of nonlinear control becomes ...

    Transient Cavitation Characteristics of Compound Centrifugal Impeller

    Jiang, Feng / Li, Huacong / Liu, Xianwei et al. | IEEE | 2021
    simulation was adopted. The steady and unsteady numerical calculations of cavitation flow in compound impeller were carried out. Monitoring points ...

    Pressure Diffusion Item to Improve Shock Robustness for Low-Diffusion Upwind Schemes

    Chen, Shu-sheng / Yang, Hua / Li, Zheng et al. | IEEE | 2021

    Riblet Surfaces for Performance Increase in Aircraft Turbines

    Leitl, Peter Adrian / Flanschger, Andreas / Lucas, Mikel et al. | IEEE | 2021
    are made just in the preliminary design phase, when materials are identified with the scope to reduce fuel consumption and mechanical wear ...

    Test Data Processing of Fly-by-Wire Civil Aircraft in Low-Speed Wind Tunnel Virtual Flight

    Tai, Shang / Wang, Lixin / Yue, Ting et al. | IEEE | 2021
    longitudinal and lateral heading control laws, and verifies the correctness of the test results by comparing the simulation data with the flight test ...

    Organizing Committees

    IEEE | 2021
    Provides a listing of current committee members and society officers. ...

    Natural Frequencies of a Simple 3D Printed Lattice Structure

    Monkova, Katarina / Monka, Peter Pavol / Vanca, Jan et al. | IEEE | 2021
    the FDM technique. Natural frequencies in the range up to 750 Hz were experimentally investigated under harmonic excitation of a linear ...

    Distributed Formation Control of Multiple Flight Vehicles with Considering Communication Delay

    Wei, Li / Qiuqiu, Wen / Huan, Jiang et al. | IEEE | 2021
    The distributed formation control of multiple flight vehicles is researched based on the reentry scenario in this paper. The leader ...

    Quality Assessment of 3D Printed Products

    Soliman, Essam / Alzahrani, Bander | IEEE | 2021
    affect the surface finish. For relatively larger dimensions, the material and nozzle size do not have a significant effect on dimensional ...

    Development of a Fuel Test Bench with Changing the Position of the Test Object in the Current Time Mode

    V, Grachev S. / S, Savelev R. / V, Mikryukov N. et al. | IEEE | 2021
    frame. All components of the system under test (fuel tanks, standard pumps, piping, and assemblies) mounted on the inner frame. Such ...

    Experiment Study of Failure Mode of HTPB/AP Interfacial Debonding

    Gong, Jian-Liang / Ma, Kai / Zhang, Jie et al. | IEEE | 2021
    binder and AP, respectively. Based on the sandwich apparatus, the energy per unit area of completely interfacial debonding without MAPO is equal ...

    Analysis of the Hydraulic System of a Long-Haul Aircraft

    Grachev, S. V. / Smagin, D.I. / Vasilyev, N. G. et al. | IEEE | 2021
    , B-787, IL-96, SSJ-100, and several others. As a result of the analysis, the most suitable version of the hydraulic system in terms of ...