1–50 of 103 hits
|

    Daring You to Ask What If? Centennial Challenges

    Hong S Kim / Monserrate C Roman | NTRS | 2018

    Analysis and prediction of the disc brake squeal considering pad damping and attached parts

    Kim,C. / Zhou,K. / Song,Y.G. et al. | Automotive engineering | 2014

    Lightweight optimal design of a rear bumper system based on surrogate models

    Li,C. / Kim,I.Y. / Queens Univ.,CA | Automotive engineering | 2015

    Pressure change and variation of vibration in an automotive disk brake system due to hot spot

    Kim,M.G. / Cho,C. / Kim,C.B. et al. | Automotive engineering | 2007

    CVT ratio control algorithm by considering powertrain response lag

    Lee,H. / Kim,C. / Kim,T. et al. | Automotive engineering | 2004

    Spacesuit Padding Design for Mobility and Comfort

    Yaritza Bernal / Alex C Gordon / Garima Gupta et al. | NTRS

    Design of a decision maker for an evasive or braking maneuver for collision avoidance

    Ackermann,C. / Isermann,R. / Min,S. et al. | Automotive engineering | 2014

    Failure modes investigation and analysis of electric power steering system with PMSM drives

    Choi,C. / Lee,W. / Kim,J. et al. | Automotive engineering | 2009

    Improvement of durability in HSDI diesel cylinder head

    Kim,B. / Chang,H. / Lee,K. et al. | Automotive engineering | 2005

    A study on the advanced technology analysis process of steering system for idle performance

    Kim,K. / Choi,I. / Kim,C. et al. | Automotive engineering | 2007

    Auditory localization of backup alarms: the effects of alarm mounting location

    Heckman,G.M. / Kim,R.S. / Khan,F.S. et al. | Automotive engineering | 2011

    Parametric study on automotive windshield defrost pattern using CFD

    Park,J. / Kim,C. / Hyundai Motor,KR | Automotive engineering | 2003

    CVT ratio control algorithm by considering powertrain response lag

    Lee,H. / Kim,C. / Kim,T. et al. | Automotive engineering | 2004

    Operating characteristics of DME-gasoline dual-fuel in a compression ignition engine at the low load condition

    Kim,K. / Bae,C. / Korea Advanced Inst.of Science and Technology,KR | Automotive engineering | 2013

    Performance and flow calculations for a gaseous H2/O2 thruster

    Kim, S. C. / Vanoverbeke, T. J. | NTRS | 1991

    On-Going Radiation Effects on FPGAs - Lessons Learned and Plans

    Berg, Melanie / Friendlich, M. / Perez, C. et al. | NTRS | 2010

    Numerical study of low-current steady arcs

    Kim, S. C. / Nagamatsu, H. T. | NTRS | 1992

    Disk plate shape optimization through flow analysis

    Lee,W.S. / Kim,J.S. / Kim,H.J. et al. | Automotive engineering | 1997

    Enhancement of offset crash performance in a short carrier front suspension vehicle

    Hong,C. / Kim,D.S. / Daewoo Motor,KR | Automotive engineering | 2002

    The effects of intake valve closing timing on engine performance and emissions in a DME compression ignition engine at low load cold start condition

    Kim,J. / Bae,C. / Korea Advanced Inst.of Science a.Technol.,KAIST,KR | Automotive engineering | 2012

    Numerical simulation of the thermal and fluid flow in engine room

    Kim,H.J. / Lee,W.S. / Kim,J.S. et al. | Automotive engineering | 1997

    Dual loop EGR optimization of a V6 3 l diesel engine for CO2 reduction

    Jo,C. / Lee,H. / Yoon,S. et al. | Automotive engineering | 2011

    Development of high performance diesel piston using bowl edge re-melting technology

    Han,S. / Kim,C. / Lee,G. et al. | Automotive engineering | 2014

    Technical advantages of vanadium SCR systems for diesel NOx control on emerging markets

    Girard,J.W. / Montreuil,C. / Kim,J. et al. | Automotive engineering | 2008

    Transmission main control orifice flow characteristics and correlations

    Kim,C. / Perng,C.Y. / Zhang,D. et al. | Automotive engineering | 2004

    Transmission main control orifice flow characteristics and correlations

    Kim,C. / Perng,C.Y. / Zhang,D. et al. | Automotive engineering | 2004

    Hydrocarbon emissions from a gas fueled spark-ignition engine under lean burn conditions

    Kim,C. / Bae,C. / Korea Advanced Inst.of Science and Technol.,KR | Automotive engineering | 1999

    Design of aluminum space frame for crashworthiness improvement

    Chung,T. / Lee,Y. / Kim,C. et al. | Automotive engineering | 1996

    Parametric study of small-bore HSDI diesel engine for the fuel efficient vehicle

    Shin,B. / Kwon,S. / Kim,C. et al. | Automotive engineering | 2000

    CFD modeling of combustion in a large bore two-stroke engine

    Kirkpatrick,A. / Kim,G.H. / Mitchell,C. et al. | Automotive engineering | 2004

    Effect of variable geometry turbocharger on HSDI diesel engine

    Cheong,J. / Cho,S. / Kim,C. et al. | Automotive engineering | 2000

    Friction-induced vibrations of window sealing systems

    Kim,U. / Krousgrill,C. / Mongeau,L. et al. | Automotive engineering | 2005

    Dynamic state battery modeling of energy and power as the state variables for EV application

    Lee,J. / Kim,C. / NamGoong,E. et al. | Automotive engineering | 1997

    Gas flows through the inter-ring crevice and their influence on UHC emissions

    Kim,C. / Bae,C. / Choi,S. et al. | Automotive engineering | 1999

    The effect of engine misfire on catalytic converter and vehicle emissions

    Kim,C. / Han,S. / Moon,S. et al. | Automotive engineering | 2000

    New approach to mitigate icing phenomenon in liquid phase injection of LPG fuel

    Lee,S. / Kim,C. / Choi,K. et al. | Automotive engineering | 2010