1–13 von 13 Ergebnissen
|

    Mathematical modeling and validation of cooling/heating effects in thermoelectric module coupled with heat sinks

    Korprasertsak, Nataporn / Leephakpreeda, Thananchai | IEEE | 2016
    Lumped parameter models of a thermoelectric module coupled with heat sinks are developed for assessment of cooling/heating performances in ...

    Design and experimental study of deployable radiator based on loop heat pipes

    Ding, Ting / Liu, Chang / Li, Meng et al. | IEEE | 2017
    after the spacecraft is on track. It can effectively improve the cooling capacity of the spacecraft. In this paper, the current research and ...

    Effect of working orientations, mass flow rates, and flow directions on thermal performance of annular thermosyphon

    Kammuang-lue, Niti / Sakulchangsatjatai, Phrut / Terdtoon, Pradit | IEEE | 2017
    , this study of which the objective is to experimentally investigate effect of working orientations, mass flow rates of heating and cooling ...

    Experimental investigation and modeling of the thermal cycling effect on the mechanical properties of CFRP

    Cuong, Le Nguyen / Dac Quang, Nguyen / Cuong, Tran Quoc et al. | IEEE | 2016
    and degradation of mechanical properties in the laminated composite material is given. It is found that after 120 heating and cooling cycles ...

    Structural Design and Verification of Hydrogen Peroxide Electric Pump

    Yuanbo, He / Yang, Liu / Jan, Wang et al. | IEEE | 2022
    pump based on hydrogen peroxide was carried out. Focus on medium and explosive problem under high temperature hydrogen peroxide, making use of ...

    Design and test of a remote steering upper port launcher for ITER

    Verhoeven, A.G.A. / Elzendoorn, B.S.Q. / Bongers, W.A. et al. | IEEE | 2005
    , the RS launching system enables to do maintenance on the system during shutdown, without affecting the torus vacuum and the blanket cooling ...

    Multi-beam CO/sub 2/ lasers and theirs applications

    Glova, A.F. / Drobyazko, S.V. / Likhanskii, V.V. | IEEE | 2005
    Description of the design and radiation parameters of multi-beam CO/sub 2/ lasers with a diffusion gas cooling and with an ac discharge ...

    Testing Needs for ITER ECH Transmission Line Components

    Olstad, R.A. / Doane, J.L. / Callis, R.W. | IEEE | 2006
    The performance requirement of 1 (possibly 2) MW cw at 170 GHz for ITER Electron Cyclotron Heating and Current Drive transmission line ...

    Ultimate cold-electron bolometer for THz applications

    Kuzmin, L. | IEEE | 2004
    ), an unavoidable dc heating for electrothermal feedback is replaced by deep electron cooling removing all incoming power from the absorber to ...

    The Primary Design of ECU for EAST

    Tonghai, Ding | IEEE | 2006
    one of the most important plasma heating and current driving methods for EAST. After referring to ECH systems operating on the other devices ...

    Regeneration of cryosorbing exhaust gas panels by means of gyrotron radiation

    Mobius, A. / Mack, A. / Day, C. et al. | IEEE | 2002
    to be disconnected from the vessel and rapidly heated (during 75 s) to 80-100 K to regenerate the surface. After heating, rapid cooling down ...

    Recent results of ECH diamond window development

    Takahashi, K. / Illy, S. / Heidinger, R. et al. | IEEE | 2004
    Resent results of a diamond window development for an electron cyclotron heating (ECH) system are reported. High power millimeter wave ...

    Progress of the 1 MW, 140 GHz, CW gyrotron for W7-X

    Dammertz, G. / Alberti, S. / Arnold, A. et al. | IEEE | 2002
    better cooling and an additional relief window at the mirror box has been built and tested. Without optimisation of the parameters in short and ...