Synonyme wurden verwendet für: Welding
Suche ohne Synonyme: title: The Paton Welding Journal

1–18 von 18 Ergebnissen
|

    Welding of titanium aluminide alloys (review)

    Chernobaj, S.V. | Tema Archiv | 2013
    dependent on development of effective technologies of their processing, including welding. In this connection the purpose of this review is analysis ...

    Laser based girth welding technologies for pipeline construction

    Keitel, S. / Neubert, J. | Tema Archiv | 2011
    the focus on increasing the welding speed at a reduced number of passes. A possible alternative is the laser-GMA hybrid welding process, since ...

    Defects of joints of high-strength rails produced using flash-butt welding

    Kuchuk-Yatsenko, S.I. / Shvets, V.I. / Didkovsky, A.V. et al. | Tema Archiv | 2013
    The investigations of defects of structure of rail joints, made by flash-butt welding, were carried out. The defects were detected at the ...

    New technology of electric arc bath welding of rails on tram and crane tracks

    Kuzmenko, G.V. / Kuzmenko, V.G. / Galinich, V.I. et al. | Tema Archiv | 2012
    New rail welding technology developed by the E.O. Paton Electric Welding Institute is described, and examples of its application at ...

    Influence of welding heating on fatigue strength of hollow structures from high-strength fine-grained steels

    Bruns, C. von / Mueller, T. / Wiebe, J. et al. | Tema Archiv | 2013
    Welding trials and technological assessment of square hollow sections of 80×80×10 mm size from steel of SG69Q grade were performed. Welds ...

    Influence of technological factors on resistance to delayed fracture of butt joints of rail steel in arc welding

    Poznyakov, V.D. / Kiriakov, V.M. / Gajvoronsky, A.A. et al. | Tema Archiv | 2011
    rail steel are given. Dependences of variations in deformability ha of butt joints with the V- and U-shaped grooves on the welding heat input ...
    Schlagwörter: mechanisiertes Schweißen

    Repair welding of intermediate cases of aircraft engines from high-temperature magnesium alloy ML10 with application of electrodynamic treatment

    Lobanov, L.M. / Pashchin, N.A. / Cherkashin, A.V. et al. | Tema Archiv | 2012
    Technology was developed for repair welding of damages in aircraft engine intermediate cases from magnesium alloy ML10. The technology ...

    On planning of repair of pressurised main pipelines based on the results of in-pipe diagnostics

    Milenin, A.S. | Tema Archiv | 2013
    welding without any interruption of transportation of a product. Planning of a certain repair method, which is an important stage of ensuring the ...

    Properties of the weld metal of two-sided welded joints on pipes made from increased-strength microalloyed steels

    Rybakov, A.A. / Semyonov, S.E. / Filipchuk, T.N. | Tema Archiv | 2013
    Two-pass two-sided welding is widely applied to manufacture large-diameter pipes for main gas and oil pipelines. It is obvious that metal ...
    Schlagwörter: beidseitiges Schweißen

    Repair explosion cladding of threaded channel of car axles

    Lobanov, L.M. / Illarionov, S.Y. / Dobrushin, L.D. et al. | Tema Archiv | 2012
    journal of wheelsets for RU1-Sh type cars. At that the cracks in the journal metal and zone of joining with repair coating as well as shrinkage ...

    Structural changes in overheating zone of HAZ metal of railway wheels in arc surfacing

    Gajvoronsky, A.A. / Zhukov, V.V. / Vasiliev, V.G. et al. | Tema Archiv | 2014
    The objective of the work is investigation of the parameters of welding thermal cycle (WTC) in arc surfacing, including heating and cooling ...

    Calculation of parameters of explosion treatment for reduction of residual stresses in circumferential welds of pipelines

    Bryzgalin, A.G. | Tema Archiv | 2013
    modes of explosion treatment of circumferential pipe welds of different dimension-type. The method is based on application of general form ...

    Modelling of processes of nucleation and development of ductile fracture pores in welded structures

    Velikoivanenko, E.A. / Rozynka, G.F. / Milenin, A.S. et al. | Tema Archiv | 2013
    metal state, in particular, in the process of welding heating. Application of the developed approaches was shown on the example of analysis of ...

    Influence of chemical composition of microalloyed steel and cooling rate of HAZ metal of pipe welded joints on its structure and impact toughness

    Rybakov, A.A. / Filipchuk, T.N. / Kostin, V.A. et al. | Tema Archiv | 2013
    One of the most difficult tasks in manufacture of the gas-and-oil line pipes, from the point of view of technology of their welding, is ...

    Cracks in welded joints of large diameter pipes and measures for their prevention

    Rybakov, A.A. / Filipchuk, T.N. / Goncharenko, L.V. | Tema Archiv | 2013
    heat-affected zone is provided considering the peculiarities of technological processes of manufacture and welding of pipes. It is shown that ...

    Consideration of pore formation at estimation of limiting state in zone of pressure vessel wall thinning defect

    Makhnenko, V.I. / Velikoivanenko, E.A. / Rozynka, G.F. et al. | Tema Archiv | 2012
    The tough fracture models allowing for pores forming in plastic flow either at non-metallic inclusions or in matrix from the microcracks ...

    Improvement of reliability of main gas pipelines by using repeated in-pipe flaw detection

    Varlamov, D.P. / Dedeshko, V.N. / Kanajkin, V.A. et al. | Tema Archiv | 2012
    It is shown that the presence of a large number of abnormalities in welded joints is hazardous for safe operation of the system of main gas ...

    Influence of deposited metal composition on structure and mechanical properties of reconditioned railway wheels

    Gajvoronsky, A.A. / Poznyakov, V.D. / Markashova, L.I. et al. | Tema Archiv | 2012
    The problem of ensuring the reliability and fatigue life of rolling stock is becoming ever more urgent with increase of transportation ...