The NASA Jet Propulsion Laboratory (JPL) successfully landed the Mars 2020 Perseverance Rover at Jezero Crater on the Martian surface. Perseverance's main mission objective is to cache Martian rock and regolith samples in hermetically sealed tubes to be brought back to Earth by future missions. To achieve this goal the rover is equipped with a 2-meter-long Robotic Arm (RA) which manipulates the Turret to interact with the surface. The Turret is comprised of science instruments and tools that enable surface sampling and science. The backbone of the Turret hardware is the Rotary Percussive Coring Drill. The science instruments, which are directly mounted to the structural housing of this drill, must be able to withstand not only the launch and entry, descent and landing (EDL) loads of the vehicle but also the dynamic percussive environment, induced by the drill throughout surface operations. This paper discusses the technical hardware design, development and testing of a vibration isolation system to protect the Scanning Habitable Environments with Raman and Luminescence for Organics and Chemicals (SHERLOC) Instrument from these dynamic environments. The hardware design aspect of this problem was limited by both size and mass constraints. The Turret is tightly configured and the physical space in which hardware can reside is restricted due to multiple axes of surface interaction points. Another driving requirement is the extreme range of thermal non-operational environment from -135C to +90C. This, in addition to SHERLOC being a heavier instrument than previously integrated on a turret, made the use of isolation systems employed on previous rover missions problematic. The final design incorporates custom wire mesh springs preloaded within titanium hexapod struts equipped with flexure ends. Custom versions of commercially available wire mesh springs were designed and tested. These custom springs differed in dimension, density and stiffness from the off the shelf options. The newly designed springs went through various stages of flight acceptance testing. Detailed physics-based modeling to understand what loads the isolation system would experience was used to define the test conditions for the springs and entire isolation subsystem. The testing program developed around this was extensive to fully characterize the isolation performance over cleanliness levels, temperature and life. Another major aspect of this work was developing a method of replicating the drill's percussive environment for performance and life testing of Turret mounted hardware. Attaching the instrument to an operating drill for testing was not a viable option. A method of using a Highly Accelerated Life Test (HALT) table was developed and applied across the project as the most representative and tunable option to physically simulate this new environment. This method, along with launch environment random vibration testing, was used to build an entire dynamic qualification and flight hardware test program. The results of the design, modeling, testing and analysis of the SHERLOC Isolation System is described throughout the following paper.


    Zugriff

    Zugriff prüfen

    Verfügbarkeit in meiner Bibliothek prüfen

    Bestellung bei Subito €


    Exportieren, teilen und zitieren



    Titel :

    Mars 2020 Perseverance Rover SHERLOC Instrument Isolation System


    Beteiligte:
    Duffy, Elizabeth (Autor:in) / Franz, Brian (Autor:in) / Orzewalla, Matthew (Autor:in) / Mathy, Greg (Autor:in) / Parsons, David (Autor:in) / Jandura, Louise (Autor:in) / Moeller, Robert (Autor:in) / Krafchak, Todd (Autor:in)


    Erscheinungsdatum :

    2022-03-05


    Format / Umfang :

    2585110 byte




    Medientyp :

    Aufsatz (Konferenz)


    Format :

    Elektronische Ressource


    Sprache :

    Englisch



    Mars 2020 Rover SHERLOC Calibration Target

    Graff, Trevor / Fries, Marc / Burton, Aaron et al. | NTRS | 2016


    SHERLOC investigation for Mars 2020

    Yingst, R. A. / Williford, K. / Wiens, R. et al. | NTRS | 2019


    My Work on Perseverance Rover (Mars 2020)

    Cameron, Matthew | NTRS | 2021


    The first 300 sols of the SHERLOC investigation on the Mars 2020 rover

    A. E. Murphy / L. W. Beegle / R. Bhartia et al. | NTRS


    Mars 2020 Perseverance Rover Surface Operations Commissioning Phase Overview

    Koch, Justin / DuCharme, Lauren / Alibay, Farah et al. | NTRS | 2022