1–11 von 11 Ergebnissen
|

    Improvement of Transient Response on a Downsized 4 Cylinder Engine for Automobile Application

    Chendil, Chellapandi / A, Guru Sankar / Sanjay, Nehal et al. | SAE Technical Papers | 2021
    , powerful and less polluting. In this study, venues of improving low end torque via improvement in volumetric efficiency as well as proper selection ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Combustion and combustion processes

    Design and Development of Intake Ports for 2-Valve & 4-Valve Configurations for Heavy Duty Off-Highway Diesel Engine

    Malkhede, Dileep / Nandgaonkar, Milankumar / Tikar, Sameer | SAE Technical Papers | 2019
    source and improvement in fuel economy.In this paper, intake port design and development process is elaborated for two different power ratings of ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Combustion and combustion processes , Simulation and modeling

    Investigations on the Effect of Injection Pressure and Timing on Noise and Vibration Characteristics of a Biodiesel Fueled Genset Engine and Artificial Neural Network Architecture

    G, Arumugam / Selvan, V. Arul Mozhi | SAE Technical Papers | 2022
    In this present investigation, combustion, noise and vibration characteristics were studied in a direct injection compression ignition ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Combustion and combustion processes

    Experimental Study on the Effect of Thermal Barrier Coating on Cylinder Head of a Semi-Adiabatic Diesel Engine

    Sundararaj, Senthilkumar / Jerome, Stanley M | SAE Technical Papers | 2017
    the engine; nearly 30% of the energy is lost due to cooling. However limitation in structural behavior of metallic materials and limited ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Combustion and combustion processes

    Experimental Investigation on CO2 Reduction in Exhaust Gases of CI Engine Fuelled with Blend of Cotton Seed Oil Methyl Ester and Diesel

    Gnanasikamani, Balaji / Marimuthu, Cheralathan / K, Sureshkumar | SAE Technical Papers | 2018
    proposed for post combustion processes, Carbon dioxide capture and storage (CCS) by the absorbent is a simple and better method for CO2 emission ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Weather and climate

    Combined Effects of Injection Timing and Fuel Injection Pressure on Performance, Combustion and Emission Characteristics of a Direct Injection Diesel Engine Numerically Using CONVERGE CFD Tool

    Soni lng, Lalitkumar Ramujagir / Deshpande, Sourabh / Puri lng, Tushar Narendra | SAE Technical Papers | 2017
    this timing is advanced to 19 degree bTDC as well as retarded to 8 degree bTDC with variation in fuel injection pressure and its effects on ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Combustion and combustion processes

    Investigations on the Effects of Chemical Treatment on Mechanical Properties of Thespesia Lampas Fiber Reinforced Composites for Automobile Applications

    N, Anantha Krishna / Katta, Lakshmi Narasimhamu / Somsole, Lakshmi Narayana et al. | SAE Technical Papers | 2023
    materials and processes. The primary objective of this study is to manufacture composites using fibers obtained from Thespesia Lampas plants, which ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Composite materials , Materials properties

    Improved Calculation Methodology for Design of Connecting Rod Considering Fatigue Loads and Stresses in IC Engine

    Shriwastava, Ajeet / Gandhul, Sachin Savleram | SAE Technical Papers | 2020
    cylinder wall thrust. It experiences complex forces of compression and tensile in cyclic manner, which repeats after each 720 (in case of 4 stroke ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Combustion and combustion processes

    Thumb Design and Optimization for Backhoe Loader

    Ghate, Amit / Langner, Kurtis / Dhotre, Sandeep et al. | SAE Technical Papers | 2019
    and mid- range backhoe machine classes use 4-tine and 2-tine thumb depending upon customer applications. The design team targeted an external ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Manufacturing processes , Collaboration and partnering

    EGR Mixer Optimization for Achieving Uniform Cylinder EGR Distribution Using 1D-3D CFD Coupled Simulation Approach to Meet Future Stage V Emission Legislation in India

    Emran, Ashraf / S K, Rajesh / Dhatkar, Samir Anant et al. | SAE Technical Papers | 2020
    non-uniform mixing of the EGR and the fresh air leads to increase in the NOx and soot compared to the homogeneous mixture due to lower ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Combustion and combustion processes , Simulation and modeling

    National Aero-Space Plane Contributions to the Automobile Industry

    Mitchell, Jennifer L. / West, William K. | SAE Technical Papers | 1994
    preserve facilities and engineering talent and expertise. Research and development capabilities can not be resurrected in an on-demand basis, and ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Manufacturing processes , Research and development