1–20 von 47 Ergebnissen
|

    Dynamic analysis and experimental study of a marine gearbox with crossed beveloid gears

    Song, Chaosheng | Online Contents | 2015
    Schlagwörter: Maschinenbau , Marine machinery

    Design Method for Screw Forming Cutter Based on Tooth Profile Composed of Discrete Points

    Jiang, Zhenwei | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau , Pumping machinery

    Development of a Suspended Backpack for Harvesting Biomechanical Energy

    Xie, Longhan | Online Contents | 2015
    Schlagwörter: Electrical equipment and supplies , Electrical machinery , Maschinenbau

    Mesh stiffness calculation using an accumulated integral potential energy method and dynamic analysis of helical gears

    Wan, Zhiguo | Online Contents | 2015
    Schlagwörter: Maschinenbau , Force and energy

    Developing World Users as Lead Users: A Case Study in Engineering Reverse Innovation

    Judge, Benjamin M | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Integrated Design and Multi-objective Optimization of a Single Stage Heat-Pump Turbocompressor

    Schiffmann, J | Online Contents | 2015
    Schlagwörter: Design and construction , Engineering design

    A Comparison of the Effectiveness of Design Approaches for Human-Friendly Robots

    Lauzier, Nicolas | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Influence of Installation Tension on Transmission Error Due to Resonance in a Synchronous Belt

    Ueda, Hiroyuki | Online Contents | 2015
    Schlagwörter: Maschinenbau , Belts and belting

    A Protocol to Address User Behavior in the Eco-Design of Consumer Products

    Zwolinski, Peggy | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Design of an Actuation Device With the Capability of Automatically Distributing External Load Based on Stability Theorems

    Zhao, Yong | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Nonlinear dynamic analysis of a new antibacklash gear mechanism design for reducing dynamic transmission error

    Besharati, S.R | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Systematic Design Optimization of the Metamaterial Shear Beam of a Nonpneumatic Wheel for Low Rolling Resistance

    Thyagaraja, Niranjan | Online Contents | 2015
    Schlagwörter: Equipment and supplies , Maschinenbau , Engineering design

    Design of a Novel Multicylinder Stirling Engine

    Pennacchi, Paolo | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau , Engineering design

    The impact of geometric variation on compressor two-dimensional incidence range

    Goodhand, Martin N | Online Contents | 2015
    Schlagwörter: Design and construction , Mechanical properties , Engineering design

    Aerodynamic Design and Analysis of a Multistage Vaneless Counter-Rotating Turbine

    Zhao, Wei | Online Contents | 2015
    Schlagwörter: Design and construction , Mechanical properties , Engineering design

    Development of Scallop Cut Type Damper Seal for Centrifugal Compressors

    Takahashi, Naohiko | Online Contents | 2014
    Schlagwörter: Design and construction , Engineering design

    Topology Optimization of Fixed-Geometry Fluid Diodes

    Zhao, Longyu | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Design of a Portable Compliant Device for Estimating the Failure-Load of Mesoscale Cemented Sand Specimens

    Ananthasuresh, G. K | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Design and Modeling of a Large Amplitude Compliant Revolute Joint: The Helical Shape Compliant Joint

    Bruyas, Arnaud | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Investigation of Nonaxisymmetric Endwall Contouring and Three-Dimensional Airfoil Design in a 1.5-Stage Axial Turbine—Part I: Design and Novel Numerical Analysis Method

    Poehler, Thorsten | Online Contents | 2015
    Schlagwörter: Equipment and supplies , Design and construction , Engineering design