1–20 von 27 Ergebnissen
|

    Investigation on the Fuel and Engine Parameters that Affect the Half Mass Fraction Burned (CA50) Optimum Crank Angle

    de O. Carvalho, Leonardo / de Azevedo Cruz Neto, Rubelmar M. / de Melo, Tadeu C. Cordeiro | SAE Technical Papers | 2012

    Operational Modal Analysis Using Durability Test Data

    Takemori, C. K. / da Silva, D. W. / Maretti de Carvalho, Daniel et al. | SAE Technical Papers | 2016

    Embedded System for Steering Assistance Based on Precise Geolocation

    Heuer, Felipe / Wolaniuk, Giordano B. / Reksiedler, Guilherme et al. | SAE Technical Papers | 2017

    Split-Injection in a Downsized Ethanol SIDI Engine Aiming to Mitigate Pre-Ignition

    Malaquias, Augusto C. T. / Filho, Fernando R. / Baeta, José G. C. et al. | SAE Technical Papers | 2017

    The Use of Split-Injection Technique and Ethanol Lean Combustion on a SIDI Engine Operation for Reducing the Fuel Consumption and Pollutant Emissions

    Malaquias, Augusto C. T. / Filho, Fernando R. / Baeta, José G. C. et al. | SAE Technical Papers | 2017

    Effects of Internal EGR on the downsized Ethanol SIDI Engine Performance and Emission

    Malaquias, Augusto C. T. / Filho, Fernando R. / Baeta, José G. C. et al. | SAE Technical Papers | 2017

    Applications of Strain Measurements to Improve Results on Transfer Path Analysis

    Ramos, A. C. R. / Melo, C. A. P. / de Oliveira, L.P.R et al. | SAE Technical Papers | 2020

    DROP HAMMER PROCESSES AND POSSIBILITIES

    de Laubenfels, C. R. | SAE Technical Papers | 1937

    Engineering Design Requirements for Thin Section Reinforced Nylon Exterior Body Parts

    de Haan, Herman / Sekhar, R. C. | SAE Technical Papers | 1979

    Reactivity Controlled Compression Ignition (RCCI) for the Mixture of Diesel Fuel and Hydrous Ethanol in a Rapid Compression Machine

    Sánchez, Fernando Z. / Loaiza, Juan C. V. / De Souza, Oberdan M. R. et al. | SAE Technical Papers | 2015

    Vehicle Rollover Sensor Test Modeling

    van Schie, C. / Chou, Clifford C. / Twisk, D. et al. | SAE Technical Papers | 2007

    Regulated and Non-Regulated Emissions from a Light-Duty Diesel Car Fueled with Different Diesel Sulfur Content

    Zotin, Fátima M. Z. / Silva, Katia C. C. / Daemme, Luiz Carlos et al. | SAE Technical Papers | 2014

    Balancing Strategy for a Battery Applied in HEV Based on Bi-directional Flyback Converter and Outlier Detection

    Marques, Felipe L. R. / Padela, Fernando F. / Aranha, Juliana C. M. S. et al. | SAE Technical Papers | 2020

    The Presence of Bifurcation in a Closed-Loop Discrete Control of a Flexible Benchmark Plant analised from the Jury Stability Criterion

    Gadelha de Souza, Luiz C. / de O. e Souza, Marcelo Lopes / Tredinnick, Marcelo R. A.C. | SAE Technical Papers | 2001

    An Analytical Approach for Discrete Controllers Design Using a New S-Z Mapping with Two Tuning Parameters

    Gadelha de Souza, Luiz C. / de O. e Souza, Marcelo Lopes / Tredinnick, Marcelo R. A.C. | SAE Technical Papers | 2002

    Oil Pump Performance Correlation between Use of Test Fluids at Room Temperature and Automotive Oils at Extreme Temperatures

    Filho, Ayres P. Andrade / do Nascimento, Edson R. / Ribeiro, Eduardo Gubbiotti et al. | SAE Technical Papers | 2012

    Constructive Parameters Analysis of Combustion Pre-Chamber Adapted in Torch-Ignition System of Otto Cycle Engine

    Cândido de Sá, D. C. / Ramalho Filho, F. A. / Valle, R. M. | SAE Technical Papers | 2003

    Powertrain Air Intake System Noise Simulation Considering 0D/1D and 3D Numeric Methodologies

    Takemori, C. K. / da Silva, D. W. / Baars, E. et al. | SAE Technical Papers | 2016

    Recent Developments in AA6016 Aluminium Type Body Sheet Product

    Lahaye, C. / Schoepen, F. / Bottema, J. et al. | SAE Technical Papers | 1998

    Environmentally Acceptable Hydraulic Fluids Based on Natural Synthetic Esters

    Steverink- de Zoete, M. C. / van Aken, R. P. / Bünemann, T. F. | SAE Technical Papers | 1998