1–16 von 16 Ergebnissen
|

    High speed machining of aluminium gear box without temperature stabilization

    Freier Zugriff
    Abilio P. SILVA / Carlos S. MATEUS / Tomasz WĘGRZYN et al. | DOAJ | 2010
    aluminium alloys. These alloys are extremely light when compared with steel, making them a perfect choice to mitigate the cars weight and machining ...
    Schlagwörter: aluminium alloy , high speed machining

    Manufacturing process of plane rim from aluminium alloy

    Drozdowski, Krzysztof / Tofil, Arkadiusz / Gontarz, Andrzej et al. | Emerald Group Publishing | 2013
    aluminium alloy based on hammer forging process. Design/methodology/approach

    – It was

     ...
    Schlagwörter: 2618A aluminium alloy

    New concepts of force measurement systems for specific machining processes in aeronautic industry

    Klocke, F. / Gierlings, S. / Adams, O. et al. | Tema Archiv | 2012
    Precise force measurements are often used for the development of machining processes. A key measure thereby is the specific cutting force ...
    Schlagwörter: Aluminium

    Analysis of deburring effectiveness and surface layer properties around edges of workpieces made of 7075 aluminium alloy

    Matuszak, Jakub / Zaleski, Kazimierz | Emerald Group Publishing | 2018
    the machining process, undesirable phenomenon occurs, which is the formation of burrs at the edges of workpieces. They occur in most elements ...
    Schlagwörter: Aluminium alloys

    Otto Fuchs AZ 93 (AA 7037) - A new aluminum alloy for high strength heavy aerospace forgings

    Hilpert, Matthias / Terlinde, Gregor / Witulski, Thomas | Tema Archiv | 2009
    requirements. The new OTTO FUCHS alloy AA 7037 (Fuchs AZ 93) was developed to have a 10 to 20 % higher yield strength than conventional Aluminum alloys ...
    Schlagwörter: Aluminium

    Zerspanen der Aluminium-Legierung AlCuMgPb - Spanbildung beim Drehen

    Documentation/Report
    Wiebach, Hans-Georg | TIB AV-Portal | 1965
    Schlagwörter: alloy / aluminium alloy , machining / aluminium alloy , aluminium alloy / machining , swarf machining

    Zerspanen der Aluminium-Legierung G-AlSi 12 CuNi - Spanbildung beim Drehen

    Documentation/Report
    Wiebach, Hans-Georg | TIB AV-Portal | 1965
    Schlagwörter: alloy / aluminium alloy , machining / aluminium alloy , aluminium alloy / machining , swarf machining

    Zerspanen der Aluminium-Legierung AlCuMgPb: Schnittvorgang im Feingefüge Variation der Spanungsdicke

    Documentation/Report
    Wiebach, Hans-Georg | TIB AV-Portal | 1971
    Schlagwörter: machining / aluminium alloy , alloy / aluminium alloy , aluminium alloy / microstructure , swarf machining

    Zerspanen der Aluminium-Legierung AlCuMgPb: Schnittvorgang im Feingefüge Variation der Schnittgeschwindigkeit

    Documentation/Report
    Wiebach, Hans-Georg / Warnecke, Günter | TIB AV-Portal | 1971
    Schlagwörter: alloy / aluminium alloy , machining / aluminium alloy , aluminium alloy / chip formation , swarf machining

    Zerspanen der Aluminium-Legierung AlCuMgPb: Schnittvorgang im Feingefüge Variation des Spanwinkels

    Documentation/Report
    Wiebach, Hans-Georg / Warnecke, Günter | TIB AV-Portal | 1975
    Schlagwörter: alloy / aluminium alloy , aluminium alloy / chip formation , swarf machining

    The influence of the cutting edge shape on high performance cutting

    Burek, Jan / Zylka, Lukasz / Plodzien, Marcin et al. | Emerald Group Publishing | 2018
    milling high-performance cutting. The main purpose of the test was to determine the possibility of increasing the efficiency of machining ...
    Schlagwörter: Aluminium alloys

    Development of a main bearing cap for an inline 6 cylinder engine

    Ilia, E. / O'Neill, M. / Lee, J. et al. | Tema Archiv | 2003
    The use of Powder Metallurgy (PM) bearing caps on aluminum alloy engine blocks represents a challenge in material machining performance. In ...
    Schlagwörter: Aluminium

    Process design for cutting compounds out of spheroidal cast iron and aluminum

    Denkena, B. / Boehnke, D. / Leon-Garcia, L. de | Tema Archiv | 2005
    machining of these different alloys means a decrease in tool life and workpiece quality in comparison to a single alloy machining. This is due to ...
    Schlagwörter: Aluminium

    Metal Cutting - Chip Formation; Cutting in Microstructure

    Warnecke, Günter / Hummel, Günter | TIB AV-Portal | 1977
    20, aluminium alloy AlCuMgPb and cast iron GG 20 during the cutting process with cutting tools of differing cutting wedges (rake angle and ...
    Schlagwörter: aluminium alloy / fine etching / chip build-up , swarf machining

    Machinery of titanium intermetallic

    Mantle, A.L. / Aspinwall, D.K. | Tema Archiv | 1997
    Gamma titanium aluminides based on TiAl are seen as potential replacements for superalloys and alloy steels in aerospace and automotive ...
    Schlagwörter: Aluminium

    Zerspanen metallischer Werkstoffe

    Warnecke, Günter / Hummel, Günter | TIB AV-Portal | 2004
    Schlagwörter: aluminium alloy / fine etching / chip build-up , swarf machining