1–20 von 47 Ergebnissen
|

    Vertically Curved Runways for Reducing Airport Environmental Impact and Increasing Aircraft Productivity

    Elham, Ali | Online Contents | 2015
    Schlagwörter: Design and construction , Engineering design

    Unsteady Computational Fluid Dynamic Analysis of the Behavior of Guide Vane Trailing‐Edge Injection and Its Effects on Downstream Rotor Performance in a Francis Hydroturbine

    Lewis, Bryan J | Online Contents | 2015
    Schlagwörter: Equipment and supplies , Design and construction , Mechanical properties , Engineering design

    Topology Optimization of Fixed-Geometry Fluid Diodes

    Zhao, Longyu | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Topology Optimization of an Automotive Tailor-Welded Blank Door

    Xu, Fengxiang | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    The impact of geometric variation on compressor two-dimensional incidence range

    Goodhand, Martin N | Online Contents | 2015
    Schlagwörter: Design and construction , Mechanical properties , Engineering design

    Systematic Design Optimization of the Metamaterial Shear Beam of a Nonpneumatic Wheel for Low Rolling Resistance

    Thyagaraja, Niranjan | Online Contents | 2015
    Schlagwörter: Equipment and supplies , Maschinenbau , Engineering design

    Should Optimal Designers Worry About Consideration?

    Ross Morrow, W | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Sensitivity of Wind Farm Output to Wind Conditions, Land Configuration, and Installed Capacity, Under Different Wake Models

    Chowdhury, Souma | Online Contents | 2015
    Schlagwörter: Buildings and facilities , Design and construction , Maschinenbau

    Riveting-Induced Deformations on Aircraft Structures

    Figueira, José Augusto Nunes | Online Contents | 2015
    Schlagwörter: Rivets and riveting , Aerospace engineering , Mechanical properties

    Physics-Based Hydraulic Damper Model for Rotor Structural Loads

    Kang, Hao | Online Contents | 2016
    Schlagwörter: Equipment and supplies , Mechanical properties , Hydraulic machinery

    Obituaries: AIAA Fellow Ghia Died in June

    Online Contents | 2017
    Schlagwörter: Research and development , Aerospace engineering , Mechanical engineering

    Nonlinear dynamic analysis of a new antibacklash gear mechanism design for reducing dynamic transmission error

    Besharati, S.R | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Multi-Objective Optimization of Conceptual Rotorcraft Powerplants: Trade-off Between Rotorcraft Fuel Efficiency and Environmental Impact

    Ali, Fakhre | Online Contents | 2015
    Schlagwörter: Design and construction , Engineering design

    Mesh stiffness calculation using an accumulated integral potential energy method and dynamic analysis of helical gears

    Wan, Zhiguo | Online Contents | 2015
    Schlagwörter: Maschinenbau , Force and energy

    Investigation of Nonaxisymmetric Endwall Contouring and Three-Dimensional Airfoil Design in a 1.5-Stage Axial Turbine—Part I: Design and Novel Numerical Analysis Method

    Poehler, Thorsten | Online Contents | 2015
    Schlagwörter: Equipment and supplies , Design and construction , Engineering design

    Integrated Design and Multi-objective Optimization of a Single Stage Heat-Pump Turbocompressor

    Schiffmann, J | Online Contents | 2015
    Schlagwörter: Design and construction , Engineering design

    Integrated Decision Making in Electric Vehicle and Charging Station Location Network Design

    Papalambros, Panos Y | Online Contents | 2015
    Schlagwörter: Design and construction , Maschinenbau

    Influence of Installation Tension on Transmission Error Due to Resonance in a Synchronous Belt

    Ueda, Hiroyuki | Online Contents | 2015
    Schlagwörter: Maschinenbau , Belts and belting

    Future Use of Large Eddy Simulation in Aero‐engines

    Tyacke, James C | Online Contents | 2015
    Schlagwörter: Design and construction , Engineering design