81–100 von 102 Ergebnissen
|

    Multi-Objective Design Exploration and its Application to Formula One Airfoils

    Watts, M. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    Numerical Characterisation of Transient Particle-Laden Supersonic Jets

    Li, S. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    Precise Autonomous Aerial Payload Delivery System Integrated with UAV and UGV

    Yakimenko, O. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    Semi-Automatic Calibration of a Strap Down Attitude and Heading Reference System

    Fatiaki, A. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    A Development of the Prediction and Optimization Tool for Wiper High Speed Performance

    Kim, Hunjae | SAE Technical Papers | 2019
    In this paper, we focused on the robust wiping performance of high speed driven condition as an important situation for vehicle safety ...
    Verlag: Society of Automotive Engineers , SAE International

    Ageing Aircraft Systems Audit - Fighting the Ageing Process

    Boykett, R. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    Special Overview Briefing: Roscosmos and Australia Perspective Cooperation Trends

    Raykunov, G. / Panichkin, N. / Ivanov, V. et al. | British Library Conference Proceedings | 2011

    The Certification and Qualification Flight Test Campaign of the Tanker KC30 for the RAAF

    Morell, M. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    The P-3 Repair Assessment Manual (RAM)

    Watters, K. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    Through-Life Support as a Service: The Role of Aircraft Manufacturers

    Webb, L. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    Old Ideas Enabled Through Modern Technology

    Craddock, D. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    The Quality of Service and Network Management of a Multi-TDL Network System

    Ding, Y. / Defence Science and Technology Organisation (Australia); Royal Aeronautical Society; Institution of Engineers Australia | British Library Conference Proceedings | 2011

    Development of Spalling Estimation Model for Ball-Type Constant Velocity Joints

    Kim, DongHyuk / Kim, Dongwan / Cho, Jeonghyeon et al. | SAE Technical Papers | 2019
    at the contact points was derived by Hertz contact theory. Third, the maximum sliding speeds at the contact points were also calculated using ...
    Verlag: Society of Automotive Engineers , SAE International

    The application of parallel computing to the design of advanced helicopter flight control systems via real-time simulation

    Lawes, S.T. / Clarke, T. / Taylor, P. | Tema Archiv | 1991
    shows that a parallel modelling approach using transputers, INMOS is not only capable of generating the required model, but is also ideally ...

    Mini High Speed HCCI Engine Fueled with Ether: Load Range, Emission Characteristics and Optical Analysis

    Johansson, Bengt / Tunestål, Per / Manente, Vittorio | SAE Technical Papers | 2007
    very low fuel consumption.The present paper describes an investigation carried out on a modified model airplane engine, on how a pure HCCI ...
    Verlag: Society of Automotive Engineers , SAE International

    Door Audio Response Hybrid Modeling and Assesment

    Durr, Alexandre / Cloix, Aurélien / Gagliardini, Laurent et al. | SAE Technical Papers | 2017
    The door response to audio excitation contributes to the overall performance of the audio system on several items. First, acting as a ...
    Verlag: Society of Automotive Engineers , SAE International

    Computation of welding distortions of complex constructions

    Urner, M. / Vogt, M. / Dolger, K. | Tema Archiv | 2008
    influence of clamping on the same structure ivestigated here. Furthermore a second and third weld seam will be added to the node. This will raise ...

    The Columbus Orbital Facility Water Loop Qualification

    Gilardi, C. / Trichilo, M. / Allen, R.D et al. | SAE Technical Papers | 1999
    representative items on the basis of the equipment development status.The First Step was aimed at evaluating the hydraulic modelling of the components ...
    Verlag: Society of Automotive Engineers , SAE International

    The Recent ESA Activity in Human Requirements Investigations

    Bichi, Alessandro F. | SAE Technical Papers | 1995
    Germany and involved a crew of 4 (3 men and 1 woman) during 60 days.The third campaign, called HUBES, has been performed in 1994 at the Simulator ...
    Verlag: Society of Automotive Engineers , SAE International