1–20 von 2,894 Ergebnissen
|

    00INT003 Advanced Cooling/Heating Concepts in US Army Vehicle Systems

    Patil, A. S. / Manzione, J. / Bolton, C. | British Library Conference Proceedings | 2000

    00SVR006 Simulation of Air Conditioning Circuits in Vehicles Under Consideration of the Engine Cooling System

    Anzenberger, T. / Marzy, R. / Hager, J. | British Library Conference Proceedings | 2000

    1D-3D Coupled Analysis for Motor Thermal Management in an Electric Vehicle

    Li, Ang / Zhou, Anjian / Yi, Heng et al. | SAE Technical Papers | 2022
    performed for control parameters including cooling fan level and electric pump speed to investigate potential optimization opportunities. Effects of ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: CAD, CAM, and CAE

    1D-3D Coupled Simulation of the Fuel Spray Propagation Inside the Air-Box of a Moto3 Motorbike: Analysis of Spray Targeting and Injection Timing

    Onorati, Angelo / Della Torre, Augusto / Montenegro, Gianluca et al. | SAE Technical Papers | 2017
    is the analysis of the fuel injection strategy both on the point of view of targeting and timing, finalized to the optimization of the ...
    Verlag: Society of Automotive Engineers , SAE International

    1D Engine Simulation Approach for Optimizing Engine and Exhaust Aftertreatment Thermal Management for Passenger Car Diesel Engines by Means of Variable Valve Train (VVT) Applications

    Özyalcin, Can / Bergmann, Dirk / Deppenkemper, Kai et al. | SAE Technical Papers | 2018
    and exhaust gas aftertreatment model on use cases of variable valve train (VVT) applications on passenger car (PC) diesel engines. The VVT ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Simulation and modeling

    1D Model for Correcting the Rate of Injection Signal Based on Geometry and Temperature Influence

    Bebber, David van / Reuter, Uwe | SAE Technical Papers | 2017
    device is extended with a flexible heating system as well as multiple pressure and temperature sensors. With the help of a one-dimensional ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Combustion and combustion processes , Simulation and modeling

    1D Modeling of Expansion tank Flow

    Sathish Kumar, S / Arthanari, Tharunnarayanan / Sundaram, V | SAE Technical Papers | 2015
    An expansion tank is an integral part of an automotive engine cooling system. The primary function of the expansion tank is to allow the ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Engine cooling systems , Simulation and modeling

    1D Simulation Accuracy Enhancement for Predicting Powertrain Cooling System Performance

    Dubey, Ritambhara Raj / Jaybhay, Sambhaji / Kapoor, Sangeet et al. | SAE Technical Papers | 2019
    design and development. Design and optimization of engine coolpack (powertrain cooling unit) to attain engine cooling performance is one of the ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Simulation and modeling

    2-Way Driven Compressor for Hybrid Vehicle Climate Control System

    Kanai, Akinobu / Iguchi, Masao / Ueda, Motohiko et al. | SAE Technical Papers | 2004
    cooling performance while the engine is stopped. Until now, when a driver needed more cooling comfort the engine has been switched back on as a ...
    Verlag: Society of Automotive Engineers , SAE International

    3-Cylinder Turbocharged Gasoline Direct Injection: A High Value Solution for Low CO2 and NOx Emissions

    Roth, Gregory / Zizelman, James / Kirwan, John E. et al. | SAE Technical Papers | 2010
    hydrocarbon emissions because fueling and air controls can be separated. In-cylinder injection with GDi also provides charge cooling benefit yielding ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Environmental regulations and standards

    3D-Analytical Method Analysis of Thermal Effect in Space Shaded Solar Panel

    Hocine, Rachida / Belkacemi, Karim / Kheris, Djamel | IEEE | 2019
    of thermal study pre-design thus to minimize the system-level thermal dissipation and then lead to higher reliability. ...

    3D CFD Coolant System Simulation for Vehicle Drive-Cycle

    Ballani, Abhishek / Srinivasan, Chiranth / Maiti, Dipak et al. | SAE Technical Papers | 2021
    MP+®. The system includes actual CAD of radiator, cooling jacket, coolant pump, bypass valve and thermostat valve. This work is in ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: CAD, CAM, and CAE , Simulation and modeling

    3D FEA Thermal Modeling with Experimentally Measured Loss Gradient of Large Format Ultra-Fast Charging Battery Module Used for EVs

    Emadi, Ali / Dronzkowski, David / David, Lamuel et al. | SAE Technical Papers | 2022
    cooling methods. In this paper, a prototype liquid cooled large format Lithium-ion battery module is modeled and tested. Experiments are conducted ...
    Verlag: Society of Automotive Engineers , SAE International

    3-Dimensional Numerical Simulation on CuO Nanofluids as Heat Transfer Medium for Diesel Engine Cooling System

    Liu, Haifeng / Yang, Shuai / Yang, Xiaolin et al. | SAE Technical Papers | 2020
    %, 1%, 3% and 5% mass concentration of nanofluids, 3-dimensional numerical simulation about flow and heat transfer process in the cooling ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Engine cooling systems

    3D Laser Anemometry in a Rotating Cooling Ribbed U-Channel

    Servouze, Y. / Gicquel, P. / Tanguy, B. et al. | British Library Conference Proceedings | 1999
    Verlag: American Institute of Aeronautics and Astronautics , Reston, VA

    3-D Modeling of Heat Transfer in Diesel Engine Piston Cooling Galleries

    Matsuo, Eduardo / Pan, Jinfeng / Nigro, Roberto | SAE Technical Papers | 2005
    reliability and durability. The piston temperature control is commonly achieved by injecting cooling oil into piston galleries, but the design of the ...
    Verlag: Society of Automotive Engineers , SAE International

    3-D Multiphase Flow Simulation of Coolant Filling and Deaeration Processes in an Engine Coolant System

    Maiti, Dipak / Saha, Rohit / Pasunurthi, Shyam Sundar et al. | SAE Technical Papers | 2024
    efficiency. However, it is expensive and time consuming to identify air entrapped locations in tests, decide on the filling strategy and make the ...
    Verlag: Society of Automotive Engineers , SAE International
    Schlagwörter: Engine cooling systems

    5th International Automobile Congress

    Engineering Index Backfile | 1954
    Construction on Passenger Car Design, H.GLAUBITZ, p 885-90; Heating of Shock Absorbers When in Service, P.KOESSLER, H.J.BEERMANN, p 891-4 ...

    10PC20 Swash Plate Type Variable Displacement Compressor for Automotive Air Conditioners

    Kobayashi, Hisao / Kawaguchi, Masahiro / Inagaki, Mitsuo et al. | SAE Technical Papers | 1992
    air conditioning cycle constantly, against changes in the vehicle cooling load and engine speed. Therefore, the 10PC20 provides comfortable ...
    Verlag: Society of Automotive Engineers , SAE International

    50cc Two-Stroke Engines for Mopeds, Chainsaws and Motorcycles with Catalysts

    Landerl, Christian J. / Laimbock, Franz J. | SAE Technical Papers | 1990
    solve have been similar. Internal measures such as optimized carburetion, cooling, piston shape and clearance, scavenging and tuning of the ...
    Verlag: Society of Automotive Engineers , SAE International