1–20 von 144 Ergebnissen
|

    Z-Pinch Magneto-Inertial Fusion Propulsion Engine Design Concept

    Miernik, Janie H. / Statham, Geoffrey / Adams, Robert B. et al. | NTRS | 2011
    industry, as well as in fusion energy research. There is a wealth of literature characterizing Z-Pinch physics and existing models (3-5). In order ...

    Wind Tunnel Model Static Aeroelastic Deformation Correction Method Based on Grid Reconstruction

    Kai, Chen / Pan, Cheng / Kun, Mao et al. | Springer Verlag | 2024
    applied to the aircraft engineering design, is regarded as a useful way to meet the design requirements. ...
    Schlagwörter: Engineering

    Variable-Stiffness Mechanisms of a Spatial 5-DOF Compliant Robot Wrist

    Li, Kangkang / Pan, Yangyang / Zhang, Xukun et al. | IEEE | 2023
    compliance control method. So as to satisfy the requirements of pose adjustment and stiffness modulation of the robot operations in a three ...
    Verlag: IEEE

    Using VHDL-AMS-Based Simulation Technology for the Design and Verification of Mechatronic Systems

    Heurung, Thomas | SAE Technical Papers | 2005
    robust mechanical components was always completed by experienced mechanical engineers. This is changing, however. The requirements of additional ...
    Verlag: Society of Automotive Engineers , SAE International

    Upgrading a 2V 1Litre / Cylinder Diesel Engine for Euro 5 Compliance

    Umashankar, N. / Mahesh, P. | SAE Technical Papers | 2013
    were reviewed and modified. Theoretical calculations on coolant flow and lub oil flow requirements were done. Physical experiments were done to ...
    Verlag: Society of Automotive Engineers , SAE International

    Transfer Alignment Method and Realization of SINS on Moving Base Based on Kalman Filter

    Cong, Mingyu / Lu, Huan / Cheng, Xianghong et al. | IEEE | 2019
    alignment technology is also proved by the mathematical simulation and the carrying test flight on Y-5 aircraft. This method basically meets the ...
    Verlag: IEEE

    Towards a more efficient approach to automotive embedded control system development

    Smith, M.H. / Elbs, M. | Tema Archiv | 1999
    emphasis is being placed on engineering tools to facilitate electronic control unit (ECU) development. This paper describes the requirements of a ...
    Verlag: IEEE Operations Center , Piscataway

    Torquemeter on sites of gyrodines

    Skorykh, V.J. / Gormakov, A.N. / Plotnikov, I.A. | Tema Archiv | 2001
    manufacturing of bearings and finite rigidity of the shaft. The requirements on these parameters for electric motors are not so stiff. But for gyrodines ...
    Verlag: IEEE Operations Center , Piscataway

    The wheel-individually steerable front axle of the research vehicle "SpeedE" - virtual design and achieved performance of the first prototype

    Schwarz, Benjamin / Eckstein, Lutz / Hesse, Lars | Tema Archiv | 2014
    highly sophisticated model is used and the requirements are met. The characteristics of the first prototypes are determined on the kinematics and ...

    The systems design approach (better late than not at all)

    Gormley, J. / Mac Isaac, D.A. | Tema Archiv | 1988
    result of a grouping of optimized components. The systems process begins with a complete definition of the system requirements, is followed by ...

    Thermal and Catalytic Regeneration of Diesel Particulate Traps

    Cikanek, H. A. / White, J. E. / Florek, J. J. et al. | SAE Technical Papers | 1983
    durability and control system requirements were identified. In the catalytic technique, Diesel fuel containing .5 gm/gal lead and .25 gm/gal copper ...
    Verlag: Society of Automotive Engineers , SAE International

    The Rise and Fall of CBM (Condition Based Maintenance)

    Stecki, Jacek S. / Rudov-Clark, Shanna / Stecki, Chris | Tema Archiv | 2013
    Aircraft and avionics, offshore, marine and other complex engineering systems often operate in harsh environmental and operational ...
    Schlagwörter: Engineering-Tool , rechnergestützte Technik

    The new low speed wind tunnel of the TU Braunschweig

    Moller, T.J. / Ortmanns, J. / El Khalfaoui, M. et al. | IEEE | 2003
    . Another option is an open test section with a jet that measures 1.3 m. The maximum Reynolds-Number is 7.5*10/sup 5/. The major improvement is the ...
    Verlag: IEEE

    The New 5-Belt Road Simulation System of the IVK Wind Tunnels - Design and First Results

    Wiedemann, Jochen / Potthoff, Juergen | SAE Technical Papers | 2003
    In 2001 the FKFS (Research Institute of Automotive Engineering and Vehicle Engines, Stuttgart) took into operation state-of-the-art 5-belt ...
    Verlag: Society of Automotive Engineers , SAE International

    The need for verification and validation techniques for adaptive control system

    Cukic, B. | Tema Archiv | 2001
    are long term space missions where communication delays to ground stations are prohibitively long, and we have to depend on the systems' local ...
    Verlag: IEEE Computer Society Press , Los Alamitos
    Schlagwörter: Soft-Computing-Technik

    The Importance of Technology Readiness in NASA Earth Venture Missions

    Wells, James E. / Komar, George J. | NTRS | 2009
    mature technology that has been modeled or demonstrated in a relevant environment (Technology Readiness Level (TRL) >5). Technology Readiness ...

    The electronic chassis of the new BMW i8 - influence and characterization of driving dynamics

    Wimmer, Christian / Fetten, Jan / Odenthal, Dirk | Tema Archiv | 2014
    Starting from the requirements, a new integrated vehicle concept including a lightweight structure of carbon fiber with a so called spilt ...

    The direct integer factorization approach to the Crochiere and Rabiner multistage FIR designs for multirate systems

    Der-Feng Huang, | IEEE | 2003
    The parameters of designing a multistage, multirate narrow-band FIR system are the total storage requirements (TSR) for the coefficients or ...
    Verlag: IEEE

    The design scheme of test bed used to test automotive ignition switches

    Wenjie Liu, / Maoqin Zhang, / Yannian Rui, | IEEE | 2003
    starting ability. So every batch of ignition switches need to be sample surveyed according to strict technique and technology requirements ...
    Verlag: IEEE

    The Design and Implementation of Extravehicular Experiments Support System for Manned Spacecrafts

    Zhao, Zhenhao / Yin, Zhao / Kang, Yong et al. | IEEE | 2023
    its large size, strong carrying capacity and human participation. In this paper, according to the requirements of extravehicular experiment ...
    Verlag: IEEE