1–19 von 19 Ergebnissen
|

Ihre Suche:
journal:(International Journal of Operations

    Aircraft control surface deflection using RBF-based mesh deformation

    Michler, Andreas K. | Tema Archiv | 2011
    sites are distributed on its faces and the evaluation is performed in the auxiliary geometry exclusively. Since the number of operations for ...

    Aircraft life management using crack initiation and crack growth models - P-3C Aircraft experience

    Iyyer, Nagaraja / Sarkar, Subhasis / Merrill, Robert et al. | Tema Archiv | 2007
    management. The first section of the paper discusses general fleet life assessment methods followed by a description of traditional US Navy method of ...
    Schlagwörter: USA (United States of America)

    Application of mesh morphing technology in the concept phase of vehicle development

    Auweraer, H. Van der / Langenhove, T. Van / Brughmans, M. et al. | Tema Archiv | 2007
    DCBs. The creation of the second set of control blocks is most time-consuming and it involves a series of morphing operations that may need to ...

    A railway wheelset optimally designed for cold press fitting

    Mastinu, Giampiero / Gobbi, Massimilano / Bon, Alessandro | Tema Archiv | 2004
    damage of the wheel seat and of the wheel bore during the relatively frequent operations of press fitting and removal of the wheel from its ...

    Assessment of need for solder in modeling potted electronics during gun-shot

    Reinhardt, L.E. / Cordes, J.A. / Haynes, A.S. et al. | Tema Archiv | 2013
    Smart projectiles use electronic components such as circuit boards with integrated circuits to control guidance and fusing operations ...

    Definition of spacing constraints for the car sequencing problem

    Lesert, Aymeric / Alpan, Gulgun / Frein, Yannick et al. | Tema Archiv | 2011
    each work station is not exceeded. Some types of vehicles require several time-consuming operations to be done on a work station and will ...

    Deformation analysis of large aerospace components during assembly

    Saadat, Mozafar / Cretin, Lylian / Sim, Roy et al. | Tema Archiv | 2009
    predict overall deformation between the alignment of the rib foot and the skin panel. The assembly operations and conditions encountered on the ...

    Design of the patient care space inside an ICU vehicle or ambulance through an optimisation model

    Sanchez, F. Javier / Garcia-Sanchez, Alvaro / Ortega-Mier, Miguel et al. | Tema Archiv | 2010

    Development and application of reduced-order modeling procedures for subsurface flow simulation

    Cardoso, M.A. / Durlofsky, L.J. / Sarma, P. | Tema Archiv | 2009
    The optimization of subsurface flow processes is important for many applications, including oil field operations and the geological storage ...

    Development of electric machine duty cycles for parallel hybrid electric Beijing city bus based on Markov chain

    Li, Wen / Lee, Tae-Kyung / Filipi, Zoran S. et al. | Tema Archiv | 2012
    This paper proposes a methodology for development of representative duty cycles for experimental evaluations of electric motor performance ...

    Effect of forming and calibration operations on the final shape of large diameter welded tubes

    Palumbo, G. / Tricarico, L. | Tema Archiv | 2005
    phase is composed by three steps: the forming of the longitudinal border of the blank (C-forming); the air bending of the C-formed blank (U ...

    Empirical manufacturing line designs in Japanese automobile plants

    Nguyen, D.M. | Tema Archiv | 2009
    that for the most based upon engineering experiences. However, the use of simulation has not been applied much in designing the ML, and a ...
    Schlagwörter: Operations Research

    Investigation on the applicability of simplified mathematical models to the roll-sloshing problem

    Francescutto, A. / Contento, G. | Tema Archiv | 1999
    the dynamic effects of liquids on board during ship operations and in the frame of current research on damaged ship behaviour. ...

    Numerical evaluation of a dual-function microporous layer under subzero and normal operating temperatures for use in automotive fuel cells

    Ko, Johan / Ju, Hyunchul | Tema Archiv | 2014
    volume for ice storage during cold-start PEFC operations. Although the benefit of using a dual-function MPL was numerically elucidated in our ...

    Scheduling dynamically positioned tankers for offshore oil offloading

    Camponogara, Eduardo / Plucenio, Agustinho | Tema Archiv | 2014
    as a decision support tool to guide engineers in daily operations. A family of valid inequalities is proposed to strengthen the MILP ...

    The berth scheduling problem with customer differentiation: a new methodological approach based on hierarchical optimization

    Saharidis, G.K.D. / Golias, M.M. / Boile, M. et al. | Tema Archiv | 2010
    The berth scheduling problem deals with the assignment of vessels to berth space in a container terminal. Defining berth schedules in ...

    Thermal models of railroad wheels and bearings

    Cole, K.D. / Tarawneh, C.M. / Fuentes, A.A. et al. | Tema Archiv | 2010
    The rolling surface for railroad wheels can be a heat source that may have an impact on the performance of the wheel bearing. In this study ...

    Two-axle bogie design for electrical multiple unit: Part 1: Finite element analysis of bogie frame fatigue strength

    Huang, Y.M. / Wang, T.S. | Tema Archiv | 1999
    bogie frame mechanical body under different loading conditions and modes of operations, then to explore structural reactions generated by ...

    Unified fluid-structure interpolation and mesh motion using radial basis functions

    Rendall, T.C.S. / Allen, C.B. | Tema Archiv | 2008
    mesh, and flow-solver type dependence is removed, and all operations are performed on totally arbitrary point clouds of any form. Hence, all ...