1–13 von 13 Ergebnissen
|

    High-Value SLM Aerospace Components: From Design to Manufacture

    Brandt, Milan / Sun, Shou-Jin / Leary, Martin et al. | Tema Archiv | 2013
    can then be built in their final shape with minimal material wastage. Samples and small product runs can be produced quickly at comparatively ...
    Schlagwörter: additive Fertigung , weltweite Fertigung

    Biomimetic Design of Lightweight Vehicle Structures Based on Animal Bone Properties

    Rui, Yan / Subic, Aleksandar / Takla, Monir et al. | Tema Archiv | 2013
    design software Mimics. Force resistance and energy absorption properties of relevant bone structures subjected to quasi-static compression loads ...

    A New Technology of Aircraft Structural Health Monitoring

    Lu, Xiao-Hua / Zuo, Hong-Fu | Tema Archiv | 2013
    . Compared with the traditional and some novel Non-Destructive Testing (NDT) techniques, it is capable of real-time crack initiation and growth ...

    Importance of Eco-Friendly OLED Lighting

    Thejokalyani, N. / Dhoble, S.J. | Tema Archiv | 2014
    investing cosmic treasures in tracking down the advanced artificial lighting applications with a vision towards energy efficient and eco-friendly ...
    Schlagwörter: Fertigung

    Topology Optimization of Suspension of the Hard Disk Drive Based on SIMP Method

    Yang, Shu-Yi / Li, Hong / Ou, Yang-Bin | Tema Archiv | 2013
    solid isotropic elastic material penalty (SIMP) method were put forward, and the suspension multi-objective topology optimization model was ...
    Schlagwörter: isotropic elastic material

    Effect of the Impact Load on the Main Welding Outer Cylinder of Large Aircraft Landing Gear

    Wang, Hong-Feng / Song, W.W. / Wang, J.L. et al. | Tema Archiv | 2013
    Analysis about the cause of the main failure and the forces of the main welding outer cylinder of the recent large aircraft landing gear ...

    Review on the Research of Dynamic Characteristics for Spacecraft Solar Arrays

    Pan, Ze-Hao / Wu, Jia-Ning / Yan, Shao-Ze et al. | Tema Archiv | 2013
    ratio, application of more advanced contact model, dynamic characteristics of solar array made of new materials and consideration of deformation ...

    Study on Safe Behavior of Electric Bicycle Braking Process

    Qiu, Xin / Yang, Qing / Wang, Sheng-hua et al. | Tema Archiv | 2011
    production standards and present a reference for the formulation of relevant traffic laws and regulations. ...

    Design of Laboratory Test Device for Evaluating the Lifetime of Hydraulic Components of Tractor Three-Point Hitch

    Hujo, Lubomir / Tkac, Zdenko / Tulik, Juraj et al. | Tema Archiv | 2013
    tractor with plough allow implementing the design and simulation of operational loads of the dynamic system of tractor three-point hitch (TPH ...

    Use of Alternative Fuels at Selected Types of Vehicles

    Zalezak, Zoltan / Bernat, Rastislav / Kecskes, Norbert | Tema Archiv | 2013
    being increasingly replaced by alternative fuels. It is caused by new technologies that allow combustion of such fuels and, at the same time ...

    Design of Body Structure for New Type Lightweight Electric Vehicle

    Wang, Li-Xia / Zhao, Tian-Feng / Cao, Jian-Bo et al. | Tema Archiv | 2014
    the weight of the vehicle effectively. Its performance becomes more advanced, and the application becomes more economical and safe. By using ...

    Real Time Monitoring System of Heat Treatment Intelligent Workshop

    Feng, Zhi-Wen / Wang, Gui-Tang | Tema Archiv | 2014
    based on networking mode, integrates material heat treatment, electronic information, computer and other subjects of advanced theory and ...
    Schlagwörter: clean production

    Chemical-Electric Car as an Undergraduate Student Project

    Wang, Qi-Chen / Lange, Thomas / Choudhary, Jay Paul et al. | Tema Archiv | 2013
    low cost, durable materials, constrained size of the car, power generation and its stability and car speed. ...