Contingent upon the modification of an initial condition of the injected or deployed orbit. Additionally, these designs can be restricted by the selection of the Cubesat subsystem design such as propulsion or communication. Nonetheless, many trajectory options can be designed with have a wide range of transfer durations, fuel requirements, and final destinations. Our investigation of potential trajectories highlights several design options including deployment into low Earth orbit (LEO), geostationary transfer orbits (GTO), and higher energy direct lunar transfer orbits. In addition to direct transfer options from these initial orbits, we also investigate the use of longer duration Earth-Moon dynamical systems. For missions with an intended lunar orbit, much of the design process is spent optimizing a ballistic capture while other science locations such as Sun-Earth libration or heliocentric orbits may simply require a reduced Delta-V imparted at a convenient location along the trajectory. In this article we examine several design options that meet the above limited deployment and subsystem drivers. We study ways that both impulsive and low-thrust Solar Electric Propulsion (SEP) engines can be used to place the Cubesat first into a highly eccentric Earth orbit, enter the Moon's Sphere of Influence, and finally achieve a highly eccentric lunar orbit. We show that such low-thrust transfers are feasible with a realistic micro-thruster model, assuming that the Cubesat can generate sufficient power for the SEP. Two examples are shown here: (1) A Cubestat injected by Exploration Mission 1 (EM-1) then employing low thrust; and (2) a CubSat deployed in a GTO, then employing impulsive maneuvers. For the EM-1 injected initial design, we increase the EM-1 targeted lunar flyby distance to reduce the energy of the lunar flyby to match that of a typical lMoon system heteroclinic manifold. Figure 1 presents an option that encompasses the similar dynamics as that of the ARTEMIS mission design. Low-thrust maneuvers are used along the manifold trajectory to raise perigee to that of a lunar orbit, adjust the timing with respect to the Moon, rotate the line of apsides, and target a ballistic lunar encounter. In this design a second flyby decreases the orbital energy with respect to the Moon, so that C3 -0.1 km2s2. Another design, shown in Figure 2 emanates from a GTO then uses impulsive maneuvers to phase onto a local Earth-Moon manifold, which then transfers the CubeSat to a lunar encounter.


    Zugriff

    Zugriff über TIB

    Verfügbarkeit in meiner Bibliothek prüfen


    Exportieren, teilen und zitieren



    Titel :

    Lunar Cube Transfer Trajectory Options


    Beteiligte:
    Folta, David C. (Autor:in) / Dichman, Don (Autor:in) / Clark, Pamela (Autor:in) / Haapala, Amanda (Autor:in) / Howell, Kathleen (Autor:in)

    Kongress:

    International Workshop on LunarCubes ; 2014 ; Sunnyvale, CA, United States


    Erscheinungsdatum :

    2014-10-07


    Medientyp :

    Sonstige


    Format :

    Keine Angabe


    Sprache :

    Englisch




    Lunar Cube Transfer Trajectory Options

    D. Folta / D. J. Dichmann / P. Clark et al. | NTIS | 2015


    Lunar Cube Transfer Trajectory Options

    Folta, David / Dichmann, Donald J. / Clark, Pamela et al. | NTRS | 2015


    Lunar Cube Transfer Trajectory Options

    Folta, David / Dichmann, Donald James / Clark, Pamela E. et al. | NTRS | 2015


    Lunar Cube Transfer Trajectory Options

    Folta D. / Dichmann D. J. / Clark P. E. et al. | NTIS | 2015


    Lunar Cube Transfer Trajectory Options

    D. C. Folta / D. Dichman / P. Clark et al. | NTIS | 2014