Abstract An oxygen-fuelled Hall Effect Thruster is investigated at the Imperial Plasma Propulsion Laboratory vacuum chamber facilities over a different range of discharge channel axial lengths, ceramic walls and anode materials. The purpose of using oxygen as a propellant is to better understand the principles of water electrolysis Hall Effect Thrusters, which are envisaged to use oxygen to propel the thruster. These studies aimed to answer whether if for molecular plasmas, a larger channel length would benefit the overall performance of the thruster by increasing the length of the ionization region, or if a shorter channel would be more beneficial due to a reduction in the energy losses associated with the plasma-wall interactions. Experimentally, it is found that channel lengths of 13.1 mm performed the best amongst the lengths tested in terms of thrust, specific impulse and thrust efficiency. Larger channels (59.8 mm, 44.8 mm and 34.8 mm) showed a reduction in thruster performance with increasing channel length. A very short channel length of 5.5 mm is found to be less efficient than the best performing case (13.1 mm), possibly indicating that the ions are being formed within or downstream of the peak acceleration region due to the constrained length of the channel. These behaviours appear to be more evident the higher the discharge power. The impact of the walls material is also investigated. In the past, changing the thruster walls from Alumina (Al2O3) to Boron Nitride (BN) made a significant improvement on the performance, generally because of the lower Secondary Electron Emission of the BN walls. In this study, two different grades of BN walls are used: 99% purity BN (grade AX05) and a BNSiO2 compound (grade M26). Although BNSiO2 walls are said to have slightly lower Secondary Electron Emission than BN, the thrust measurements obtained using these walls are very similar. Finally, anodes made out of different materials are also tested. The main goal is to identify a suitable anode material that prevents a non-conductive oxidation layer to be formed when in contact with the oxygen plasma. Tungsten anodes are found to develop, after just a few hours of testing, a non-conductive layer that prevents the long-term operation of the thruster. Stainless steel anodes however, generate an oxidation layer which is still conductive and did not compromise the functionality of the thruster throughout the duration of the experimental campaigns. The highest thrust measurement obtained was 27 . 0 ± 0 . 2 mN; corresponded to a specific impulse of 2874 ± 21 s and a thrust efficiency of 17 . 00 ± 0 . 25 %; for a discharge power of 2238 ± 1 W using a channel length of 13.1 mm.

    Highlights Performance measurements of an oxygen-fuelled Hall Effect Thruster. Determination of the best performing discharge channel axial length (13 mm). Investigation of different anode materials in contact with the oxygen plasma. Investigation of different ceramic Boron Nitride Grade walls.


    Zugriff

    Zugriff prüfen

    Verfügbarkeit in meiner Bibliothek prüfen

    Bestellung bei Subito €


    Exportieren, teilen und zitieren



    Titel :

    An oxygen-fuelled Hall Effect Thruster: Channel length, ceramic walls and anode material experimental analyses


    Beteiligte:
    Tejeda, J.M. (Autor:in) / Knoll, A. (Autor:in)

    Erschienen in:

    Acta Astronautica ; 203 ; 268-279


    Erscheinungsdatum :

    2022-11-28


    Format / Umfang :

    12 pages




    Medientyp :

    Aufsatz (Zeitschrift)


    Format :

    Elektronische Ressource


    Sprache :

    Englisch





    Analyses of the anode region of a Hall Thruster cahnnel

    Keidar, Michael / Boyd, Iain / Beilis, Isak | AIAA | 2002


    Channel length and thruster performance of Hall thrusters

    Komurasaki, Kimiya / Mikami, Kenji / Kusamoto, Daisuke | AIAA | 1996



    Channel length and wall recombination effects in the Hall thruster

    Cohen-Zur, A. / Gany, A. / Fruchtman, A. et al. | AIAA | 2000